View TLP2066_4124927.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLP2066
TOSHIBA PHOTOCOUPLER GaAAs IRED & PHOTO-IC
Preliminary
FA (Factory Automation) High Speed Interface 3.3V Supply Voltage
TLP2066
Unit in mm
The Toshiba TLP2066 consists of a GaAAs light-emitting diode and an integrated high-gain, high-speed photodetector. TLP2066 operates with 3.3 V supply voltage. Toshiba provides the TLP116 for supply voltage 5V type. Inverter logic (totempole output) Package type : MFSOP6 Guaranteed performance over temperature : -40~100C Power supply voltage : 3.0~3.6V Input thresholds current: IFHL=5mA (Max.) Propagation delay time (tpHL/tpLH): 60ns (Max.) Switching speed : 20MBd(TYP.)(NRZ) Common mode transient immunity : 15kV/us Isolation voltage : 3750Vrms UL recognition: UL1577 under application TOSHIBA Weight: 0.09 g(Typ.) 11-4C2
Pin Configuration (Top View)
1
VCC
6 5
1: ANODE 3: CATHODE 4: GND 5: VO 6: VCC
Truth Table
Input H L LED ON OFF Tr1 OFF ON Tr2 ON OFF Output L H 3
GND SHIELD
4
Schematic
ICC 6 Tr1 IO Tr2 VO 5 VCC
IF 1+ VF 3-
SHIELD
4
GND
0.1uF bypass capacitor must be connected between pins 6 and 4
1
2007-11-20
TLP2066
Absolute Maximum Ratings (Ta=25C)
Characteristic
Forward current LED Forward current derating (Ta85C) (Note1) Symbol IF IF/Ta IFPT VR IO VO VCC PO Topr Tstg Tsol (Note2) BVs Rating 25 -0.7 1 6 10 6 6 40 -40~100 -55~125 260 3750 Unit mA mA/C A V mA V V mW C C C Vrms
Peak transient forward current Reverse voltage
DETECTOR
Output current Output voltage Supply voltage Output power dissipation
Operating temperature range Storage temperature range Lead solder temperature(10s) Isolation voltage (AC,1min.,R.H.60%,Ta=25C)
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note1: Pulse width PW1us, 300pps. Note2: This device is regarded as a two terminal device: pins 1 and 3 are shorted together, as are pins 4, 5 and 6.
Recommended Operating Conditions
Characteristic Input current , ON Input voltage , OFF Supply voltage(*) (Note3) Symbol IF(ON) VF(OFF) VCC Min 8 0 3.0 Typ. Max 18 0.8 3.6 Unit mA V V
-- --
3.3
(*) This item denotes operating ranges, not meaning of recommended operating conditions. Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. Note3: The detector of this product requires a power supply voltage (VCC) of 3.0 V higher for stable operation. If the VCC is lower than this value, an ICCH may increase, or an output may be unstable. Be sure to use the product after checking the supply current, and the operation of a power-on/-off. Note 4: A ceramic capacitor(0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypass may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm.
2
2007-11-20
TLP2066
Electrical Characteristics (Unless otherwise specified, Ta=-40~100C, VCC=3.0~3.6 V)
Characteristic Input forward voltage Temperature coefficient of forward voltage Input reverse current Input capacitance Logic low output voltage Logic high output voltage Logic low supply current Logic high supply current Supply voltage Input current logic low output Input voltage logic high output Symbol VF VF/Ta IR CT VOL VOH ICCL ICCH VCC IFHL VFLH Test Circuit Conditions IF=10mA ,Ta=25C IF=10mA VR=6V,Ta=25C V=0,f=1MHz,Ta=25C IOL=1.6mA, IF=12mA IOH=-0.02mA, VF=1.05V IF=12mA, VCC=3.3V VF=0V, VCC=3.3V (Note 3) Min. 1.45 Typ. 1.6 2 Max. 1.85 Unit V mV/C A pF V V mA mA V mA V
-- -- -- --
1 2 3 4
-- -- -- --
2.0
--
10
--
60
--
0.6
-- -- -- -- -- -- --
--
5.0 5.0 3.6 5
-- --
3.0
-- -- --
--
IO=1.6mA,VO<0.6V IO=-0.02mA,VO>2.0V
--
0.8
--
*All typical values are at Ta=25C, VCC=3.3V, IF (ON) =12mA unless otherwise specified
Isolation Characteristics (Ta = 25C)
Characteristic Capacitance input to output Isolation resistance Symbol CS RS Test Conditions Vs = 0, f = 1MHz R.H. 60%,VS = 500V AC,1 minute Isolation voltage BVS AC,1 second,in oil DC,1 minute,in oil (Note 2) Min. 1x10
12
Typ. 0.8 10
14
Max.
Unit pF Vrms Vdc
(Note 2)
3750
10000 10000
Note 4: A ceramic capacitor(0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypass may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm.
3
2007-11-20
TLP2066
Switching Characteristics (Unless otherwise specified, Ta=-40~100C, VCC=3.3V)
Characteristic
Propagation delay time to logic high output Propagation delay time to logic low output Propagation delay time to logic high output Propagation delay time to logic low output Switching time dispersion between ON and OFF Output fall time (90-10%) Output rise time (10-90%) Common mode transient immunity at high Level output Common mode transient immunity at low level output *All typical values are at Ta=25C Note 5: CL is approximately 15pF which includes probe and Jig/stray wiring capacitance. CML CMH 7 VCM=1000Vp-p,IF=12mA, Vo(Max)=0.8V,Ta=25C -15000 Symbol tpHL 5 tpLH tpHL 6 tpLH |tpHLtpLH| tf 5 IF=120mA VIN=03.3V (IF=08mA) VIN=3.30V (IF=80mA) CL=15pF (Note 5) IF=012mA IF=120mA RIN=100 CL=15pF (Note 5) Test Circuit Conditions IF=012mA RIN=100 CL=15pF (Note 5) RIN=220 CIN=47pF CL=15pF (Note 5) Min. Typ. Max. 60 60 60 60 30 Unit ns ns ns ns ns ns ns
-- -- -- -- -- -- --
-- -- -- -- --
4 5
IF=12mA , RIN=100,
-- -- --
tr
VCM=1000Vp-p,IF=0mA, Vo(Min)=2V,Ta=25C
15000
--
V/s
--
--
V/s
TEST CIRCUIT 1: VOL
IF
TEST CIRCUIT 2: VOH
6 VCC 5
0.1uF
1
1
6 VCC 5
V
0.1uF
3
GND 4
VOL
V
IOL
VCC 3 SHIELD
IOH VCC
SHIELD
GND 4
TEST CIRCUIT 3: ICCL
IF 1
TEST CIRCUIT 4: ICCH
6 VCC 5
ICCL
A
1 VCC 3 SHIELD
VCC
6 5 4
ICCH
A
VCC
3 SHIELD
GND
4
GND
4
2007-11-20
TLP2066
TEST CIRCUIT 5: tpHL , tpLH
IF=12mA (P.G)
(f=5MHz, duty=50% tr =tf =5ns) INPUT MONITORING NODE
VCC
Vo 0.1uF MONITORING NODE
IF VO
VCC
50% tf tr
90%
VOH
SHIELD CL=15pF RIN=100
GND
CL=15pF
1.5V
tpHL tpLH
10%
VOL
CL is capacitance of the probe and JIG. (P.G): Pulse Generator
TEST CIRCUIT 6: tpHL, tpLH
VIN=3.3V (P.G)
(f=5MHz, duty=50% tr = tf =5ns) INPUT MONITORING NODE
VCC 0.1uF
CL=15pF
Vo MONITORING NODE
VIN VO
VCC
50% tf tr
90%
VOH
GND SHIELD CIN=47pF RIN=220
CL=15pF
1.5V
tpHL tpLH
10%
VOL
CL is capacitance of the probe and JIG. (P.G): Pulse Generator
TEST CIRCUIT 7: Common-Mode Transient Immunity Test Circuit
90% SW A B 3 SHIELD VCM SW A: IF=12mA
1000V
IF
1
6 VCC 5 GND 4 0.1uF VO VCC SW B: IF=0mA 2V 0.8V CML CMH 10% tr tf
800(V) CM = H tr(s)
800(V) CM = L t (s) f
5
2007-11-20
TLP2066
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
20070701-EN
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer's own risk. * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. * GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically. * Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
6
2007-11-20

▲Up To Search▲

Price & Availability of TLP2066

	To Download TLP2066 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .